? 2013 teledyne relays (800) 284-7007 ? www.teledynecoax.com ccp-18 page 1 ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches environmental and physical characteristics operating temperature ?40c to 65c vibration (mil-std-202 method 214, condition d, non-operating) 10 g?s rms shock (mil-std-202 method 213, condition d, non-operating) 500 g?s standard actuator life 1,000,000 cycles connector type 7/16 din humidity (moisture seal) available weight 9 oz. (255.2g) (max.) part number description ccp-18d commercial normally open multi-throw, dc-3ghz, low pim these switches have extremely low passive intermodulation for use in narrow bandwidth communications applications. the ccp-18d is a broadband multi-position coaxial switch designed to switch rf signals from one input port to any one of 3 or 4 output ports. it is designed for 50 ohms transmission line systems. the standard actuator gives individual solenoid control of each position and when de-energized, all positions are open. part numbering system for additional options, please contact factory. actuator voltage ccp-18 d 1 3 c - t ** series connectors actuator type options number of positions * 15 pin d-sub connector (see connector pinout page) connector actuator voltage number of positions actuator type options d : 7/16 female 1: 28 vdc normally open 3: sp 3 t 0 : no indicator contacts t : ttl drivers with diodes 2: 15 vdc normally open 4: sp 4 tc : indicator contacts d : coil transient suppression diodes 3: 12 vdc normally open s : d - sub connector * 4: 24 vdc normally open td : decoders and ttl drivers with diodes m : moisture seal ** see parts list on page 8 performance characteristics frequency dc?3 ghz insertion loss, db, max. 0.35 isolation, db, min. 70 vswr , max. 1.3:1 rf power (cw), w, max. 200 electrical characteristics form factor multi-throw, break before make frequency range dc?3 ghz characteristic impedance 50 ohms switching time 20 ms (max.) actuation voltage available 12 15 24 28 v actuation current, max. @ ambient 600 480 300 270 ma passive intermodulation characteristics tone 1 frequency (mhz) tone 2 frequency (mhz) im3 frequency (mhz) pim threshold (dbc) 1945 1990 1900 -140.0 p1 p2 (dbm) pim (dbc) peak pim (dbc) 43 -159.6 -156.6
ccp-18d page 2 specifications are subject to change without notice ? 2013 teledyne coax switches ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches schematics and mechanical outline ?- s option ? 15- pin d - sub connector ( example : ccp -18 n 160- s ) 1 9 p/n: voltage: vdc d/c: m/o: rohs made in teledyne coax switches schematic shown in normally open position
? 2013 teledyne relays (800) 284-7007 ? www.teledynecoax.com ccp-18 page 3 ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches 1 9 15-pin d-sub connector connector pinout for normally open sp3t multi-throw switches e xample ccp-18d130-s ccp-18d13c-s ccp-18d130-ts ccp-18d13c-ts ccp-18d130-tds ccp-18d13c-tds i ndicator y es y es y es ttl y es y es d ecoders & ttl y es y es pin no. 9-p in 9-p in 9-p in 9-p in 9-p in 9-p in 1p ort 1p ort 1p ort 1p ort 1l ogic 1l ogic 1 2p ort 2p ort 2p ort 2p ort 2l ogic 2l ogic 2 3p ort 3p ort 3p ort 3p ort 3 4e i ndicator e i ndicator e i ndicator 5f i ndicator f i ndicator f i ndicator 6g i ndicator g i ndicator g i ndicator 7c ommon c ommon c ommon c ommon c ommon c ommon 8v sw v sw v sw v sw 9d i ndicator (com) d i ndicator (com) d i ndicator (com) connector pinout for normally open sp4t multi-throw switches e xample ccp-18d140-s ccp-18d14c-s ccp-18d140-ts ccp-18d14c-ts ccp-18d140-tds ccp-18d14c-tds i ndicator y es y es y es ttl y es y es d ecoders & ttl y es y es pin no. 9-p in 15-p in 9-p in 15-p in 9-p in 15-p in 1p ort 1p ort 1 ttl 1 ttl 1 l ogic 1l ogic 1 2p ort 2p ort 2 ttl 2 ttl 2 l ogic 2l ogic 2 3p ort 3p ort 3 ttl 3 ttl 3 l ogic 3l ogic 3 4p ort 4p ort 4 ttl 4 ttl 4 5 6 7c ommon c ommon c ommon c ommon c ommon c ommon 8v sw v sw v sw v sw 9d i ndicator (com) d i ndicator (com) d i ndicator (com) 10 n / a e i ndicator n / a e i ndicator n / a e i ndicator 11 f i ndicator f i ndicator f i ndicator 12 g i ndicator g i ndicator g i ndicator 13 h i ndicator h i ndicator h i ndicator 14 15
ccp-18d page 4 specifications are subject to change without notice ? 2013 teledyne coax switches ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches truth table normally open ccp-18dx4c-td logic input rf path indicator switches 123 j1j2j3j4 efgh 000 on off off off c 000 100 off on off off 0 c 00 010 offoff on off 0 0 c 0 1 1 0 off off off on 000 c 1 1 1 off off off off 0 0 0 0 truth table normally open ccp-18dx3c-td logic input rf path indicator switches 12 j1j2j3 efg 00 on off off c 00 10 off on off 0 c 0 01 offoff on 00 c 1 1 off off off 0 0 0 truth table normally open ccp-18dx3c-t logic input rf path indicator switches 123 j1j2j3 efg 100 on off off c 00 010 off on off 0 c 0 001 offoff on 00 c truth table normally open ccp-18dx4c-t logic input rf path indicator switches 1234 j1j2j3j4 efgh 1000 on off off off c 000 0100 off on off off 0 c 00 0010 offoff on off 0 0 c 0 0 0 0 1 off off off on 000 c
? 2013 teledyne relays (800) 284-7007 ? www.teledynecoax.com ccp-18 page 5 ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches typical broadband rf performance curves rf notes -140 -120 -100 -80 -60 -40 -20 0 0 0.5 1 1.5 2 2.5 3 isolation ( db ) frequency ( ghz ) isolation ( dc-3 ghz ) 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 0 0.5 1 1.5 2 2.5 3 vswr frequency ( ghz ) vswr ( dc-3 ghz ) -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 00.511.522.53 insertion loss ( db ) frequency ( ghz ) insertion loss ( dc-3 ghz )
ccp-18d page 6 specifications are subject to change without notice ? 2013 teledyne coax switches ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches power handling vs. frequency estimates based on the following reference conditions: ? ambient temperature of 40c or less ? sea level operation ? load vswr of 1.20:1 maximum ? no high-power (hot) switching please contact teledyne coax switches for derating factors when applications do not meet the foregoing reference conditions. typical power performance curve 3000 power (w) frequency ghz 2000 1000 800 600 400 300 200 100 80 60 40 30 20 10 .1 .2 .3 .4 .6 .8 1 2 7/16 din connector switch 3
? 2013 teledyne relays (800) 284-7007 ? www.teledynecoax.com ccp-18 page 7 ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches actuator an actuator is the electromechanical mechanism that transfers the rf contacts from one position to another upon dc command. arc suppression diode a diode is connected in parallel with the coil. this diode limits the ?reverse emf spike? generated when the coil de- energizes to 0.7 volts. the diode cathode is connected to the positive side of the coil and the anode is connected to the negative side. date code all switches are marked with either a unique serial number or a date code. date codes are in accordance with mil- std-1285 paragraph 5.2.5 and consist of four digits. the rst two digits de ne the year and the last two digits de ne the week of the year (yyww). thus, 1032 identi es switches that passed through nal inspection during the 32nd week of 2010. indicator indicators tell the system which position the switch is in. other names for indicators are telemetry contacts or tellback circuit. indicators are usually a set of internally mounted dc contacts linked to the actuator. they can be wired to digital input lines, status lights, or interlocks. unless otherwise speci ed, the maximum indicator contact rating is 30 vdc, 50 ma, or 1.5 watts into a resistive load. isolation isolation is the measure of the power level at the output connector of an unconnected rf channel as referenced to the power at the input connector. it is speci ed in db below the input power level. multi-throw switch a multi-throw switch is a switch with one input and three or more output ports. the ccp-18 can switch a microwave signal to any of 2,3,4,5 or 6 output from a single common input. switching time switching time is the total interval beginning with the arrival of the leading edge of the command pulse at the switch dc input and ending with the completion of the switch transfer, including contact bounce. it consists of three parts: (1) inductive delay in the coil, (2) transfer time of the physical movement of the contacts, and (3) the bounce time of the rf contacts. ttl switch driver option as a special option, switch drivers can be provided for both failsafe and latching switches, which are compatible with industry-standard low-power schottky ttl circuits. td-option this option includes a decoder. the 3-bit parallel command is decoded to internally select the appropriate position. see the logic tables. the td-option increases the vsw supply current demand by 50ma max at 28vdc and +20c. performance parameters vs frequency generally speaking, the rf performance of coaxial switches is frequency dependent. with increasing frequency, vswr and insertion loss increase while isolation decreases. all data sheets specify these three parameters as ?worst case? at the highest operating frequency. if the switch is to be used over a narrow frequency band, better performance can be achieved. actuator current vs temperature the resistance of the actuator coil varies as a function of temperature. there is an inverse relationship between the operating temperature of the switch and the actuator drive current. for switches operating at 28 vdc, the approximate actuator drive current at temperature, t, can be calculated using the equation: magnetic sensitivity an electro-mechanical switch can be sensitive to ferrous materials and external magnetic elds. neighboring ferrous materials should be permitted no closer than 0.5 inches and adjacent external magnetic elds should be limited to a ux density of less than 5 gauss. glossary i a [1 + .00385 (t-20)] where: i t = actuator current at temperature, t i a = room temperature actuator current C see data sheet t = temperature of interest in c i t =
ccp-18d page 8 specifications are subject to change without notice ? 2013 teledyne coax switches ccp-18\072013\q3 series ccp-18d low pim multi-throw dc?3 ghz normally open coaxial switch coax switches normally open ccp-18d part number list * x = 1 (28vdc), 2 (15vdc), 3 (12vdc) and 4 (24vdc) p art n o .p art n o . 1 ccp-18dx3c 43 ccp-18dx40 2 ccp-18dx3c-d 44 ccp-18dx40-d 3 ccp-18dx3c-dm 45 ccp-18dx40-dm 4 ccp-18dx3c-m 46 ccp-18dx40-m 5 ccp-18dx3c-ms 47 ccp-18dx40-ms 6 ccp-18dx3c-s 48 ccp-18dx40-s 7 ccp-18dx3c-t 49 ccp-18dx40-t 8 ccp-18dx3c-td 50 ccp-18dx40-td 9 ccp-18dx3c-tdm 51 ccp-18dx40-tdm 10 ccp-18dx3c-tdms 52 ccp-18dx40-tdms 11 ccp-18dx3c-tds 53 ccp-18dx40-tds 12 ccp-18dx3c-tm 54 ccp-18dx40-tm 13 ccp-18dx3c-tms 55 ccp-18dx40-tms 14 ccp-18dx3c-ts 56 ccp-18dx40-ts 15 ccp-18dx30 16 ccp-18dx30-d 17 ccp-18dx30-dm 18 ccp-18dx30-m 19 ccp-18dx30-ms 20 ccp-18dx30-s 21 ccp-18dx30-t 22 ccp-18dx30-td 23 ccp-18dx30-tdm 24 ccp-18dx30-tdms 25 ccp-18dx30-tds 26 ccp-18dx30-tm 27 ccp-18dx30-tms 28 ccp-18dx30-ts 29 ccp-18dx4c 30 ccp-18dx4c-d 31 ccp-18dx4c-dm 32 ccp-18dx4c-m 33 ccp-18dx4c-ms 34 ccp-18dx4c-s 35 ccp-18dx4c-t 36 ccp-18dx4c-td 37 ccp-18dx4c-tdm 38 ccp-18dx4c-tdms 39 ccp-18dx4c-tds 40 ccp-18dx4c-tm 41 ccp-18dx4c-tms 42 ccp-18dx4c-ts
|
